The point about being disposable wasn't that they couldn't be sharpened, but that someone representing Mayfell, thought users would buy new rather than sharpen. This is fine if the blade costs £15 but not if the thing costs £50 in my book. Maybe this reflects on the quality of the blade that we're getting?
I've now tried it out with the re-re-ground blades and it seems fine in green oak at full depth cut. Using it free-hand It wouldn't move when a bit of twist bound the saw-plate in the kerf. Still don't know what my earlier problem was, unless the rails were rocking and that caused binding.
I'm a bit late reading this thread, but happened to notice it and it seems as good a place as any to ask if anyone knows of a good saw blade sharpener in the UK (for me, it would be for 48t 162mm blades, for an MT55cc).
A firm that reliably sharpens to the same geometry as the original, rather than choosing a geometry they feel it should be.
I can find plenty of firms on the internet, but, never having had any blades sharpened by any of them, I have no way of knowing who does a good job and without altering the geometry.
Post by huntsgemein on Aug 31, 2017 7:31:30 GMT -5
Most sharpening shops have adjustable settings for face & hook angles. Once setup, each tooth gets the same treatment; first one side, then the other. Any reputable Saw doctor can achieve as good as OEM results & geometry.
If in doubt, write your required settings (hook, face & rake angles) from the mnf'rs website, their catalogue or sawblade packaging onto the Saw plate with a contrasting texta pen. Don't assume the doctor can guess the appropriate tooth geometry. This allows the shop to preset their diamond sharpening disc to the appropriate setting/s.
If anything, smaller blades with higher tooth counts tend to be expensive to doctor. Most Saw shops charge by the tooth.
bengt: Oh please the ks60 is better in every way. 60 degree miter in both directions. Bevels past 45(essential in a saw that must cut on the flat) Bigger blade more capacity. The Metabo hpt has 57 degree miter max and 45 bevel max.
Sept 9, 2019 20:02:24 GMT -5
abdon: I stand corrected , the angle fence is only attaches with F -Tracks , what confused me was , that the Timberwolf site mentioned it will work with the NFU machine, yes it will work but only I guess when you use the Ftrack , with other tracks Like the KSS L.
Nov 28, 2020 22:52:01 GMT -5
glynnco: Did you order from GereedschapPro? I see them as in stock but I'm located in the US and am not sure if they ship here. I sent them an email asking about shipping but it was returned undeliverable...
Dec 10, 2020 7:37:40 GMT -5
jonathan: I've purchased a lot of stuff from our neighbours @ GereedschapPro.nl As far as I know they are one of the larger Mafell dealers in the EU. I can recommend them, they usually respond quickly.
Dec 11, 2020 13:58:36 GMT -5
NFU 50 Transportation?: Hi Guys, is there some Systainer for the NFU 50?
Dec 11, 2020 14:30:12 GMT -5
frezik24: Hello everyone
Dec 13, 2020 9:20:00 GMT -5
frezik24: Could somone help me?
Dec 13, 2020 9:20:10 GMT -5
frezik24: I can't access the board even though i'm logged in on proboards...
Dec 13, 2020 9:20:51 GMT -5
jonathan: @frezik24 I can't find anything regarding an account with username frezik24. No account, no post history and no ban history.
Dec 13, 2020 12:17:59 GMT -5
jonathan: I would recommend you create a new account. If there is nothing to be found, there is unfortunately nothing to restore.
Dec 13, 2020 12:18:55 GMT -5