would any of the members in the united states be interested in this kit? hoping to do a group thing. probably cost a little over $300 plus shipping from nebraska. i know a couple guys on here already have it and I'm pretty sure they are happy with it. maybe the can chime in. comes with what you see here
Same here. I've not got a need for anything but the quick clamps and I haven't found a source for the Bosch FSN KZW quick clamps that will ship to the US. I find that the stock Mafell screw clamps occasionally loosen from the vibration of the saw. Anyone else experience that problem?
I haven't noticed my screw clamps loosen from vibration but I have bent them a little bit from not sliding them all the way into the rail then tightening. I would try the Bosch ones if I could find them too but as it is I really don't use the clamps much anyway. The rail stays put really well without the clamps.
You can directly order it from Amazon.de now, they lifted whatever shipping embargo they had on sending the 800mm kit to the US. Shipping is actually pretty reasonable usually and you need to remember to remove VAT off the prices.
For the long holey rails you're still stuck. I ordered my two 1.6m holey rails from Dictum since Amazon.de wouldn't ship the kit a few months back.
Post by toomanytoys on Sept 15, 2016 9:29:13 GMT -5
Btw, I ordered the kit from Amazon.de yesterday after setting up an account there. My US version of Amazon would not pull up the item. With shipping it totaled out at $145 USD. Shipping is expected in about 10 days I believe.
For the next person that orders some, then I could use some of the d-handled clamps... (Or I'll do some big order through Germany.)
once I get through things in a few weeks I'll try to get back to how to make aluminum feet on a router table that will attach to bar clamps in the same manner as these Bosch units. On occasion I've used the small clamp version and they work fine. You guys seen to want the bigger version, which I haven't gotten to.
Picked up the Bosch clamps from amazon.de and they are quite nicely made and far less fidgety than the ultra-short screw-handled ones, but their inability to fit through an MFT or other bench dog hole at all is a massive dealbreaker for me personally. I'll probably use one to steady the far end of a KSS rail when I'm starting the super heavy 80 along it, but otherwise they're not really for me. Surprised there's no official offering between the short-and-flimsies and the Aerofix in terms of price, but the Aerofix is pretty nice.
abdon: I stand corrected , the angle fence is only attaches with F -Tracks , what confused me was , that the Timberwolf site mentioned it will work with the NFU machine, yes it will work but only I guess when you use the Ftrack , with other tracks Like the KSS L.
Nov 28, 2020 22:52:01 GMT -5
glynnco: Did you order from GereedschapPro? I see them as in stock but I'm located in the US and am not sure if they ship here. I sent them an email asking about shipping but it was returned undeliverable...
Dec 10, 2020 7:37:40 GMT -5
jonathan: I've purchased a lot of stuff from our neighbours @ GereedschapPro.nl As far as I know they are one of the larger Mafell dealers in the EU. I can recommend them, they usually respond quickly.
Dec 11, 2020 13:58:36 GMT -5
NFU 50 Transportation?: Hi Guys, is there some Systainer for the NFU 50?
Dec 11, 2020 14:30:12 GMT -5
frezik24: Hello everyone
Dec 13, 2020 9:20:00 GMT -5
lasse: Thanks for the tip! I have own a mafell rail which is 160 cm and one that is 80 cm. Will it work just as well or will I need to buy rail that is 110 cm?
Mar 18, 2021 15:35:15 GMT -5