|
Post by GhostFist on Jan 20, 2016 16:19:22 GMT -5
The arunda is built for the 65. There was talk of it being compatible with the 2200 but I never heard further. I'd doubt the 2200 fits the mafell router table stock but mafell did design the 2200's predecessor so I could be wrong.
|
|
|
Post by holmz on Jan 20, 2016 16:27:14 GMT -5
I would not be surprise d if they designed the 1400. It looks a lot like the LO-50. All the Elu/Mafell/DeWalt and FT cross branding it is confusing.
It is like stoning ones long lost twin sister for being from a different race.
|
|
|
Post by GhostFist on Jan 20, 2016 16:33:41 GMT -5
Mafell was involved in designing festool routers at on point. Just like mafell crossed over with bosch and metabo. Legend has it that they became snotty with each other because initial domino 500 designs supposedly stole the pin referencing mechanism from mafell's dd40. Ever since then any mention of mafell on a festool forum is met with hostility.
Illuminati confirmed!
|
|
|
Post by GhostFist on Jan 20, 2016 16:35:54 GMT -5
Forgot to add this
|
|
|
Post by jimbouk on Jan 20, 2016 16:39:52 GMT -5
Mafell was involved in designing festool routers at on point. Just like mafell crossed over with bosch and metabo. Legend has it that they became snotty with each other because initial domino 500 designs supposedly stole the pin referencing mechanism from mafell's dd40. Ever since then any mention of mafell on a festool forum is met with hostility. Illuminati confirmed! Domino with the dd40 pin reference system would be sweet!
|
|
|
Post by GhostFist on Jan 20, 2016 16:59:47 GMT -5
That's what the original dominos had. They were forced to switch to the paddle stops. I like the click away stops on the 700 though.
|
|
kdjb
New Member
Posts: 23
|
Post by kdjb on Jan 21, 2016 8:07:18 GMT -5
Finally got a measurement for the OF-2200 On the Festool owners group
It is 198mm apparently and 7-1/2 to 7-5/8 is between 190.5mm and 193.675mm A bit dissapointed if the measurements are correct
|
|
|
Post by GhostFist on Jan 21, 2016 8:40:25 GMT -5
What are you measuring here?
|
|
|
Post by thedude306 on Jan 21, 2016 9:08:10 GMT -5
He's measuring the base of the FSN OFA and the base of the OF 2200 (I think)
|
|
kdjb
New Member
Posts: 23
|
Post by kdjb on Jan 21, 2016 9:34:38 GMT -5
He's measuring the base of the FSN OFA and the base of the OF 2200 (I think) Correct! 198mm for the base of the OF-2200 and between 190.5 and 193.675mm for the base of the FSN-OFA so if these measurements are correct it's too big Sort of expected it...
|
|
|
Post by thedude306 on Jan 21, 2016 9:36:10 GMT -5
What all are you planning to do with the FSN OFA? I've used it with a bosch colt and plunge base and it works excellent.
|
|
kdjb
New Member
Posts: 23
|
Post by kdjb on Jan 21, 2016 9:45:13 GMT -5
i just wanted to mount a Festool OF-2200 in it but it looks like the 2200s base is too big
|
|
|
Post by GhostFist on Jan 21, 2016 10:12:37 GMT -5
Couldn't you just make your own guide by kerfing a block to the dimensions of the lip on the rail and attaching it to the router with guide rods?
|
|
|
Post by Knight Woodworks on Jan 21, 2016 10:36:52 GMT -5
Minor hijack: Someone asked if the 2200 will fit in the Ericka. None of the Festool routers will work "as is". Mafell does make an adapter that may do the trick.
Carry on.
John
|
|
kdjb
New Member
Posts: 23
|
Post by kdjb on Jan 21, 2016 12:11:30 GMT -5
Couldn't you just make your own guide by kerfing a block to the dimensions of the lip on the rail and attaching it to the router with guide rods? I feel in this case i would be better off just giving in Buying a Festool rail and mounting kit, I like the superior design of the FSN-OFA and would rather have 5mm removed from the base of the router than be held to ransom by Festool or just buy a 2000w Bosch and a OF-1010 and save my self the hassle completely Minor hijack: Someone asked if the 2200 will fit in the Ericka. None of the Festool routers will work "as is". Mafell does make an adapter that may do the trick. Carry on. John Going to look into this right now
|
|