|
Post by kalas on Jan 12, 2015 10:55:26 GMT -5
I had Steve Adams at Qwas make me a set of dogs for Mafell F rails. The holes in my table are 22mm so adapting the standard 20mm MFT rail dogs wouldn't work. Looking good in Mafell red! I highly recommend writing to Steve if you would like something similar. steve@qwasproducts.com Attachments:
|
|
|
Post by mick on Jan 12, 2015 13:38:17 GMT -5
Hi Kalas Very nice are the t bolts for the mafell track and did he supply them as well ? I was on to him last week but he was having problems posting to Ireland I have to get back on to him next week Hopefully i can get some
|
|
|
Post by kalas on Jan 12, 2015 15:15:50 GMT -5
Hi Mick,
Yes they are. He supplied the nut to fit a Mafell rail. I hope he can ship these to you. The shorter once were modified a bit since this photo was taken. I wanted the threads to go all the way through them.
|
|
|
Post by mick on Jan 12, 2015 16:59:17 GMT -5
Kalas thanks for that I think he will ship them he said some had gone missing in the post going to Ireland over the Christmas he was hoping to sort it out I will email him next week
|
|
|
Post by MrToolJunkie on Jan 18, 2015 11:45:32 GMT -5
Hey Kalas - these are very nice. Was there an upcharge for them or regular pricing? How much lead time did it take?
|
|
|
Post by Tom Gensmer on Jan 18, 2015 17:49:32 GMT -5
Hey Kalas - these are very nice. Was there an upcharge for them or regular pricing? How much lead time did it take? These are actually '"normal" Qwas dogs, but with a bolt appropriate for the Mafell tracks. I had mine shipped without an anodized finish, it's a little easier to fit them in the MFT holes.
|
|
|
Post by kalas on Jan 19, 2015 10:50:38 GMT -5
Hi, no upcharge. The red powdercoat was included and bolt to fit F rails. These were custom size 22mm diameter for my table and Steve had them done in a week. Great service. The smaller dogs were low profile and threaded all the way through the center. In the photo above they weren't finished. I highly recommend the Qwas products.
|
|
|
Post by MrToolJunkie on Jan 19, 2015 22:08:28 GMT -5
Good to know...thanks Kalas and Tom.
I do have a couple of QWAS prodcts and agree that they are top notch.
|
|
|
Post by mick on Jan 22, 2015 13:01:38 GMT -5
I was back on to Steve today and unfortunately he is not shipping to Ireland any more due to postal problems so I will try and get some made up here
|
|
|
Post by jimbouk on Jan 24, 2015 3:14:39 GMT -5
I ordered some to the uk and they never turned up. Lost out bad on that one. He wasnt very helpfull either.
|
|
|
Post by jonathan on Jan 24, 2015 3:25:07 GMT -5
I got my dogs here: precisiondogs.us/store
I like how they have a small recess just below the lip that rests on the table. Ensures that the dogs slip all the way into the hole.
|
|
|
Post by mick on Jan 24, 2015 5:40:51 GMT -5
Hi jimbouk yes he reckons that for Ireland people are ordering them getting them and claiming they didn't get them I am sure some people may do but I would not thing for the small amount of people in Ireland buying these it is likely he must think the same for the uk sorry to here you lost out.
Hi Jonathan Thanks for that link I have just ordered two sets of rail dogs from them will save me trying to get them made up here
|
|
|
Post by mick on Feb 9, 2015 13:05:07 GMT -5
Got the rail dogs in the post today will hopefully get s chance to try them This week Thanks again for the link Jonathan
|
|
|
Post by kalas on Feb 10, 2015 10:44:53 GMT -5
The first set of low profile dogs that we had custom made were a bit snug so Steve made another set free of charge. I have nothing but positive experience with Qwas. Great service and good stuff.
|
|